超微粉碎机厂家

咨询热线

13256798563

当前位置:首页-新闻动态-行业新闻-低温超微粉碎机设备在实际的使用中应该注意什么?

neixin.png

低温超微粉碎机设备在实际的使用中应该注意什么?

低温超微粉碎机在实践操作中我们发现,有很多客户需求粉碎热敏性的物料和塑料。这两类物料是粉碎行业的难点,特别是实验剖析这一块,简直是空白。经过与台湾方面的不时沟通和实验,终于用“液氮罐配合FDV粉碎机"这种方式处理了这个难题。由于该机所用的钢材材质非常优秀,关于低温的液氮完整能够接受,这样边投料边参加液氮,就处理了这个问题。从而使得该机的应用范围极度扩展。关于普通的塑料,可粉碎至60-120目左右。
In practice, we find that many customers need to crush thermosensitive materials and plastics. These two kinds of materials are the difficulty of crushing industry, especially the experimental analysis, which is almost blank. After frequent communication and experiments with Taiwan, the problem was finally solved by the way of "liquid nitrogen tank cooperating with FDV crusher". Because the steel material used in this machine is excellent, the liquid nitrogen at low temperature is completely acceptable, so that the problem can be solved by adding liquid nitrogen while feeding. Thus, the application range of the machine is greatly expanded. For ordinary plastics, it can be crushed to about 60-120 meshes.
低温超微粉碎机实践操作技巧:
Practical operation skills of cryogenic ultrafine grinder:
这里只讲下FDV气引式粉碎机一些非常有用的小诀窍。投料时zui好投到刀片中心螺丝上,这样有利于物料疾速平均的向周围散开,使得粉碎即快又细;投料速度要少而快,即一次少投点但频率要快,综合下来看,比其他办法粉碎速度快且省设备;本机装备了三种刀型的刀片,假如合理应用,也能起到事半功倍的效果。假如物料比拟好粉碎,如化学合成类、粉性足的中药材,能够用大弯刀;物料有一定粘性选用大弯刀,但大弯刀粉碎细度不如直刀;假如直刀粉碎效果不好时可选择中弯刀,细度要高些。
Here are some very useful tips for FDV air-driven crusher. When feeding, Zui is good to throw on the center screw of the blade, which is helpful for the material to disperse rapidly and averagely to the surrounding area, making crushing fast and fine; feeding speed should be less and fast, i.e. fewer feeding points at a time but faster frequency, in a word, it is faster and less equipment than other methods; this machine is equipped with three types of blades, if Reasonable application can also achieve twice the result with half the effort. If the material is comparable to the crushing, such as chemical synthesis, crushing foot of Chinese medicinal materials, can use a large bender; material has a certain viscous choice of large bender, but the fineness of large bender crushing is not as good as straight knife; if the effect of straight knife crushing is not good, choose medium bender, fineness is higher.
中药超微粉碎机的留意事项
Notices for the Superfine Crusher of Traditional Chinese Medicine
中药超微粉碎机的留意事项:
Notices for ultra-fine crusher of traditional Chinese medicine:
1.粉碎物投入量勿越过粉碎碗容量1/2.
1. The input amount of crushing material should not exceed 1/2 of the capacity of crushing bowl.
2、枯燥物料粉碎得更细。不宜加工湿润和油脂物品
中药超细粉碎机
2. Dry materials are crushed finer. Not suitable for processing wet and greasy articles
3、刚开机时,若碰到粉碎物卡住刀片,使电机不能正常运转,要立刻关闭电源,避免电机损坏,清算后才干重新工作
3. When the machine is just started, if the blade is stuck in the crushed material, so that the motor can not work properly, the power supply should be switched off immediately to avoid motor damage, and then work again after liquidation.
4、普通中药粉碎只需1分钟,特殊需求时间加长一些。粉碎时间不宜过长,避免细粉发热粘粉碎碗。
4. It takes only 1 minute to comminute ordinary Chinese medicines, and the time for special needs is longer. The crushing time should not be too long, so as to avoid the heat of fine crushing and sticking to the crushing bowl.
5、本中药超微粉碎机不能长时间连续工作,每次不要越过5分钟,加工数量多时,中间必需要休息,避免电机轴承过热形成电机损坏。
5. The ultra-fine crusher of this traditional Chinese medicine can not work continuously for a long time. It should not exceed 5 minutes at a time. When the processing quantity is large, it must rest in the middle to avoid motor damage caused by overheating of motor bearings.
6、长时间运用,要正常检查碳刷与刀片磨损水平。视状况改换配件
6. When using for a long time, the wear level of carbon brush and blade should be checked normally. Replacement of accessories as appropriate
7、避免机器掉到地上损坏机器,应安顿相对稳定的工作台
7. To avoid the machine falling to the ground and damaging the machine, a relatively stable worktable should be installed.
8、若发现电机不能正常工作,检查线路或查看保险丝
8. If it is found that the motor is not working properly, check the circuit or check the fuse
9、中药超微粉碎机上盖翻开时,不要开机工作
9. Don't turn on the top cover of the ultra-fine crusher of traditional Chinese medicine when it is turned over.
10、保修期为一年,终身维修
10. Warranty period is one year, life-long maintenance

济南骏程机械设备有限公司

PHONE

13256798563 / 400-766-9788 

E-mail

junchengweifen@163.com

ADDRESS

济南市市中区袁庄会龙工业园

Website

http://www.jnjuncheng.com

  • 手机客户端
  • 客服微信

首页 / 关于我们 / 产品中心 / 工程案例 / 新闻动态 / 服务和支持 / 联系我们 /

版权所有:济南骏程机械设备有限公司 备案号: 鲁ICP备15034461号-3 技术支持: 济南诺商信息 网站地图 XML TXT 流量统计: